Advanced Formwork Systems L.L.C
Zulin Formwork & Scaffolding Sole Agent In Jordan
Adjustable Column Formwork KTZM
|
Product Name：Adjustable Column Formwork |
Characteristics
Efficient forming of any shape and size.
High columns ,multiple formwork re-uses,high requirements for the quality of the finished facework.
Column size,straight from the modular system for speedy forming of any permit column cross-section with standard parts .
Vertical waling has two standards for quadrate column or rectangular column with their sides in 400～1200mm.
Turn the size of 800×800mm to the size of 400×400mm, the rest may be deduced by analogy, you can complete any dimension in this scope .
Framed Formwork GK-120
Product Name：Framed Formwork
Product Type：GK-120
Product Description：The framed formwork is a hollow steel structure covered with plywood.
Characteristics of GK120 series wall formwrok
1、 The framed formwork is a hollow steel structure covered with plywood. The plywood is 18 mm thick and in good quality.
2、As a highly standardized system, it is flexible to assemble, and wood batten can be filled in to satisfy the need for nonstandard size.
3、The formwork is also highly strengthened, and the wall formwork can bear lateral pressure of 60 KN/m2 ,while the column formwork can support 80 KN /m2.
4、The adjustable clamps are convenient to use and hold firmly.
5、There is a prizing part designed in the corner, which can help to position and remove formwork easily.
6、The formwork is screwed on from the back when connecting frame and plywood, and the surface of the finished concrete is perfect.
7、The formwork series are a complete system with a full set of accessories, and can be installed flexibly according to project demand.
1050 series /750 series adjustable column formwork
1050 series /750 series adjustable column formwork are used in the concrete pouring of square or rectangle column. The largest column dimension is 1050x1050mm and 750x750mm. Combined the two together, the rectangle column can be done，the largest dimension is 1050x750mm. Additionally，wood batten（width≤50mm） can be filled in the corner to satisfy the middle dimension. The sketches are shown below:
C series vertical formwork is the column formwork series. They are matched with column waler. The cross section sketches are shown below:
|
The section perimeter of the a square or rectangle column:300~850mm；The diameter of a round column:φ250~φ800mm. |
The section perimeter of the a square or rectangle column:500~1350mm；The diameter of a round column:φ450~φ1300mm. |
The Arrangement Of Column Formwork:
Framed Formwork Works with Other Systems
Adjustable Arced Formwork KTYH
Product Name：Adjustable Arced Formwork
Product Type：KTYH
Product Description：Adjustable arced formwork is utilized in concrete pouring of arced wall or column with radius more than 1m.
Adjustable arced formwork is utilized in concrete pouring of arced wall or column with radius more than 1m.
Working principle
The plywood of adjustable arced formwork is 18mm thick with certain toughness. It can resist certain pressure and be adjusted to designed arc.
Assembly procedure
1. Assemble timber beam and timber connector.
2. Assemble plywood and edge rib.
3. Assemble adjustable system.
4. Assemble connecting waling.
5. Adjust the formwork, make the formwork bent into designed radius.
6. Connect every module by adjustable steel clamp.
Single Side Bracket
Product Name：Single-side Bracket
Product Type：
Product Description：Single-side Bracket for concreting single face walls.
Single-side Bracket for concreting single face walls. Cost-effectiveness is improved when designing in construction site with reasonable stress. High level of universality and standardization for components .
It is used for outside wall of basement, the sewage treatment plant as well as protection wall of the slope of a road or bridge and so on. Usually, the operating space for highest Single-side Bracket is 4m width. The maximum pouring height is 7.5m one time.
The single-side bracket consists of two parts, anchor system and bracket. Brackets are designed to suit lorry and container loading dimensions.
The anchor system includes: anchor rod, joint nut, joint rod, wing nut and cast washer plate. Brackets have three specification in terms of height : standard frame H=3600mm, heighten frame H=500mm, heighten frame H=1600mm.
Also works with timber beam formwork and GK120 System for Higher efficiancy and less cost.
Simple Single Side Bracket
Product Name：Simple Single-side Bracket
Product Type：
Product Description： It is a newly developed single-side bracket on the basis of the common one.
Simple single-side bracket is based on single-side bracket. Compared with single-side bracket, simple single-side bracket has simpler structure. It is easy to assemble and disassemble, and convenient for transportation and storage.
Steel Column Formwork
