Advanced Formwork Systems L.L.C
Zulin Formwork & Scaffolding Sole Agent In Jordan
Slab Table Formwork System TM
|
Product Name：Table Formwork |
Introduction
Table formwork is a kind of formwork specializing in floor slab concreting，and it is widely used in highrise buildings, skyscrapers, multi-storey industrial factory buildings, underground structures, etc. Standard as well as nonstandard table formwork can be set up to meet the requirements of slabs in different shapes and dimensions. Advantages of the formwork are easy structure, simple assembly and disassembly, flexible location, and multiple using times. By the specially designed lifting fork, the whole table formwork unit can be lifted and repositioned, thus speeding up the construction cycle and saving much labor cost, too.
Fast repositioning reduces the labor costs.
The table formwork has simple structure, it is easy to assemble and disassemble and can be reused .
Practical shifting trolley make for virtually fatigue-free operations.
Fully assembled units are manoeuvred quickly into place.
Easier to handle and safer than hand-operated formwork, particularly as room heights increase.
Lifting fork can reposition table formwork easily and reliably on the construction site.
It's effortless removal from underneath the cast slab.
For transportation to the next storey and for truck loading and unloading.
With shifting trolley and attachable drive unit so that one man can move up to 11.9 M2 of formwork complete with accessories on one level without the assistance of a crane.
Standard size is 2440mmx4880mm and 3300mmx5000mm.
Special sizes for special applications can be supplied at any time.
Standard functional components can be installed for straightforward, speedy adaptation to changing requirement on the construction site.
Generally guardrails are installed on the edge of the table formwork, so that a ring fence comes into being to secure the construction work.
Non Standard Slab Formwork
Product Name：Nonstandard Slab Formwork
Product Type：
Product Description：Nonstandard slab formwork is widely used in concrete pouring of slabs. Floor props or scaffoldings with supporting heads are utilized as the supporting system. Timber beams are used as main and secondary beams, which are covered with plywood.
Introduction
Nonstandard slab formwork is widely used in concrete pouring of slabs. Floor props or scaffoldings with supporting heads are the supporting system. The main beam and secondary beam are timber beams with plywood on the topside. The system has many advantages, such as simple structure, easy assembly and dismantling, flexible location and being able to reuse.
The supporting head series:
In concrete pouring of the slabs, supporting head series support the slab formwork. Some of them can move early or quickly. Subject to the demand, various kinds of supporting heads are able to work together, thus making construction work much more efficient.
Early Striking Disassembly Progress
After concreting, hit the pin plate to let it move.
When the pin plate move to the right position, the movable part of the head and main beam will come down.
Remove the main beam for reuse.
Lowering Head Disassembly Progress
After the concrete pouring, hit the pin plate to let it move.
When the pin plate move to the right position, the main beam, secondary beam and plywood will come down in order.
Remove the timber beams, plywood, lowering heads and floor props.
Shifting Trolley TC
Product Name：Shifting Trolley
Product Type：TC
Product Description：Shifting trolley is used for transporting table formwork on the same floor.
Introduction
Shifting trolley is used for transporting the table formwork unit on the same floor. It mainly consists of two parts, the standard device and attached frame(if needed). During transporting, push the shifting trolley to the place just below the center of table formwork unit, adjust the height of the trolley manually by a handle, and lift the formwork unit. Then move the trolley (with the formwork unit on it) to the designated position, lower the trolley manually, leave the table formwork unit on the ground and finally remove the trolley.
Height:
※ Standard device
Hmin=1750mm Hmax=3250mm
※ Standard device with an attached frame
Hmin=2500mm Hmax=3900mm
Bearing load：
※ Standard device：1100kg（11kN）
※ Standard device with an attached frame：1000kg（10kN）
Lifting Fork TJ
Product Name：Lifting Fork
Product Type：TJ
Product Description：Lifting fork is used for lifting table formwork units. All connection pins must be inserted into the correct holes before working.
Lifting fork is used for lifting table formwork units. All connection pins must be inserted into the correct holes before working.
Lifting fork is able to reposition table formwork units easily and reliably on the construction site.
The designed bearing load of the lifting fork is 1-1.5T, and it is exclusively used for lifting table formwork units, which means it is not allowed for hoisting any other tools or equipment. For purpose of the stability of formwork unit, two prongs shall be forked between the main beams. If it is inconvenient to do so, they may support the main beams directly, in which case, the main beam and prong cross each other. However, this kind of situation should always be avoided.
.
When concrete pouring finishes，lift the table formwork unit to an upper floor.
Beam Clamp UJJ
Product Name：Beam Clamp
Product Type：LJJ
Product Description： Beam clamp is one instrument for supporting the beam formwork.
Introduction
Beam clamp is one instrument developed and manufactured by ZULIN specially for supporting the beam formwork. It has simplified the way of installing formwork and therefore, has greatly enhanced the efficiency of construction work. Beam clamp can work together with beam or wood batten alongside a formwork unit, while on the bottom, the formwork shall be fixed by timber beam and beam clamp. Floor props or scaffoldings are to be used as the supporting system, and plywood as the panel.
Beam Clamp A Application Sketch
Only using beam forming support, the pouring height can reach 350mm at most.
dding extension for beam forming support, the maximum pouring height can be 758mm.
Beam Clamp B Application Sketch
Only using beam forming support, the pouring height can reach 800mm at most.
Adding extension for beam forming support, the maximum pouring height can be 1225mm.